DETWILER HYDRAULIC JACKPLATE

This topic has 15 replies, 8 voices, and was last updated 10 years, 3 months ago by bwp777.

Viewing 15 posts - 1 through 15 (of 16 total)

1 2 →

Author

Posts
September 15, 2011 at 3:33 pm #423807

gchagler
Participant

Look at the holes on the side of the outside plate and you should see some grease fittings.

September 15, 2011 at 3:59 pm #423809

3broscat
Participant

thank you sir.btw what is this SEBCOG tournament being talked about on here? if its GUNTERSVILLE thats a long way from VA

September 15, 2011 at 4:38 pm #423811

gchagler
Participant

No Problem. Its the South East Bass Cat Owners Group tournament. Its put on by owners and is a gathering for BCB fellowship, and a tourney. It is on Guntersville and is Oct. 1st and 2nd.

September 15, 2011 at 11:26 pm #423813

clownshoes
Participant

Only 2 shafts have grease zerks. Those are the two large outside ones. The center piston is the shaft of a 115 merc trim motor. If thats is squeaking then spray shaft with wd or similar. If the center shaft is rubbing make sure jackplate motor is secure where it is fastened to jackplate. Ask me how i know…had screws that were loose on mine recently….motor rubbed hard enough to short….caught big motor ground on fire…8 miles downstream…at night….with dbasket screaming “who cares if its one fire!!!burn this blue POS UP!!!” Not somethin i wanna repeat.C.O.D. Jr. III

September 21, 2011 at 4:27 pm #423815

3broscat
Participant

the starboard side top and bottom shaft hex bolts loosened up.red loctite on both,reinstalled.good to go! no loctite on previosly.WHY? oh well.

September 21, 2011 at 4:39 pm #423817

Bass Cat Boats
Keymaster

Dude I gots not idea. Just knew to check it!C.O.D. Jr. III

September 21, 2011 at 7:11 pm #423819

Bass Cat Boats
Keymaster

Post removed as it was in error. Last edited by Bass Cat Boats on September 21st, 2011, 11:06 pm, edited 1 time in total.

September 21, 2011 at 7:28 pm #423821

3broscat
Participant

its a 2010 jackplate still under warranty.does detwiler know of this update or have implemented it since 2010?

September 21, 2011 at 11:02 pm #423823

clownshoes
Participant

BCB are you saying if any are loose we should replace with new screws? There isnt a screw on mine that hasnt been loose at some point.C.O.D. Jr. III

February 26, 2014 at 9:59 pm #315713

Tideman
Participant

My plate works fine at idle, but while running it will come up but wont go down. Anyone have this problem ?

February 26, 2014 at 10:35 pm #315732

Bass Cat Boats
Keymaster

That is an older plate and the four (4) main stem bolts should be tensioned every few months of use.

February 26, 2014 at 10:53 pm #315750

Tideman
Participant

THANKS AGAIN…..

February 26, 2014 at 11:45 pm #315767

PhilAddison
Participant

You might need to add a little grease to the support bars. Zerks are on the side and can be accessed through the side of the jack plate. Any type of grease.

February 16, 2016 at 2:50 am #450262

Bass Cat Boats
Keymaster

Possibly low on fluid. Detwilers have no issue on power usually.

February 16, 2016 at 11:48 am #450263

jigging
Participant

Thanks I will check it
Author

Posts

Viewing 15 posts - 1 through 15 (of 16 total)

1 2 →

You must be logged in to reply to this topic. Login Register